Yamaha htr-6040 manual

Table Of Contents. Quick Links. See also: Service Manual. Table of Contents. AV Receiver. Previous Page. Next Page.

Basic operations Page 6: Features W 1 kHz, 0. Page 7: Getting Started Snap the battery compartment cover back into place. Front speakers Place your speakers in the room and connect them to this unit.

Page Connections See page 21 for connection information. See pages 16 and 19 for connection information. Page Placing Speakers Center speaker C The center speaker is for the center channel sounds dialog, vocals, etc.

If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system.

If this type of speaker still creates interference with the monitor, place the speakers away from the monitor. Note A speaker cable is actually a pair of insulated cables running side by side.

Page Setting The Speaker Impedance Cables are colored or shaped Caution differently, perhaps with a stripe, groove or ridges. Do not discard the cap. This cap protects the jack from dust. To enjoy the sound from speakers connected to this unit, — make an analog or digital connection besides the HDMI connection see page VIDEO connections see page Page Connecting To Component Video Jacks Note Be sure to connect your video components in the same way you connect your video monitor to this unit.

For example, if you connect your video monitor to this unit using a HDMI connection, connect your video components to this unit using the HDMI connection. Be sure to match the left and right output jacks to the left and right input jacks for the front and surround channels. In general, these antennas should provide sufficient signal strength. This unit employs the YPAO Yamaha Parametric Room Acoustic Optimizer technology which lets you avoid troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically.

The supplied optimizer microphone collects and this unit analyzes the sound your speakers produce in your actual listening environment.

The connected subwoofer is turned on and the volume level is set to about half way or slightly less. The crossover frequency controls of the connected subwoofer is set to the maximum. Optimizer microphone. It is recommended that you use a tripod etc. You can use the attached screw of a tripod etc. You can also select the following setup methods. Once you perform the next operation, this unit starts the automatic setup procedure.

For more accurate measurements, keep quiet and move to the wall where speakers are not around. We recommend that you leave the listening room during the automatic setup procedure. This unit starts the auto setup procedure. Loud test tones are output from each speaker during the auto setup procedure.

Once all items are set, the result display appears in the OSD. It takes approximately 3 minutes for this unit to complete the auto setup procedure. Checks which speakers are connected and the polarity of each speaker. Also checks and adjusts the volume level of each speaker. Checks the distance of each speaker from the listening position and adjusts the timing of each channel. Checks the frequency response of each speaker and sets the appropriate low-frequency crossover for each channel.

Displays the speaker distance from the listening position in the following order:. The optimizer microphone is sensitive to heat. Keep it away from direct sunlight and do not place it on top of this unit.

Check the warning messages to correct your speaker settings. See page 32 for details. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation, e If the product has been dropped or damaged in any way, and f When the product exhibits a distinct change in perfor- mance - this indicates a need for service.

XM Satellite Radio tning Getting started. Voltages are as follows: Asia model Preparation: Check the items Prepare the following items. Speakers Front speaker The priority of the requirement of other speakers is as follows: 1. Two surround speakers 2.

Center speaker Active subwoofer Speaker cable DVD player Video monitor Video cable Digital coaxial audio cable Step 1: Set up your speakers Place your speakers in the room and connect them to this unit.

Front and center speakers To the center speaker To the front To the front right speaker left speaker Surround speakers. DVD player AV receiver. Refer to the instruction manual of the DVD player for further information.

What do you want to do with this unit? Connections Placing speakers The speaker layout below shows the speaker setting we recommend. Center speaker C The center speaker is for the center channel sounds dialog, vocals, etc.

Surround left and right speakers SL and SR The surround speakers are used for effect and surround sounds. Subwoofer SW The use of a subwoofer with a built-in amplifier, such as the Yamaha Active Servo Processing Subwoofer System, is effective not only for reinforcing bass frequencies from any or all channels, but also for high fidelity sound reproduction of the LFE low-frequency effect channel included in Dolby Digital and DTS sources.

Surround speakers Right Left. Connecting the banana plug except Europe, Russia, Korea, and Asia models The banana plug is a single-pole electrical connector widely used to terminate speaker cables. Banana plug. AUDIO jacks For conventional analog audio signals transmitted via left and right analog audio cables.

Connections Connecting other components Make sure that this unit and other components are unplugged from the AC wall outlets. Connections Connecting audio components Connect the audio components as follows. L R L R out Front. Caution Be sure to turn down the volume of this unit and other components before making connections. DOCK 2. Game console or Portable audio video camera player. Assembling the supplied AM loop antenna Note The types of the supplied AM loop antenna is different depending on the models.

Connecting the power cable Once all connections are complete, plug the power cable into the AC wall outlet. Refer to the right column for details. Note The setting you made is reflected next time you turn on this unit. C Multi-information display Shows the name of the current sound field program and other information when adjusting or changing settings.

Optimizing the speaker setting for your listening room This unit employs the YPAO Yamaha Parametric Room Acoustic Optimizer technology which lets you avoid troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically. Note Before starting the automatic setup, check the following check points.

Speakers are connected appropriately. Headphones are disconnected from this unit. This unit and the video monitor are turned on. This unit is selected as the video input source of the video monitor. The room is sufficiently quiet. Optimizer microphone The following display appears in the OSD. Optimizer microphone y It is recommended that you use a tripod etc. The following message appears in the OSD. Please keep quiet or leave the room. Speaker size SIZE Checks the frequency response of each speaker and sets the appropriate low-frequency crossover for each channel.

Optimizing the speaker setting for your listening room The display changes as follows. You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual. Buy as many as you need. Receiver must not be plugged in while connecting speakers.

FM antenna. Keeping receiver unplugged, connect as shown. Connect Center Speaker Wire. Antenna Connection. FM Antenna. AM Loop Antenna.

Inspect Contents After unpacking, inspect the contents to confirm you have the above items:. RCA cable. Yamaha manuals. Text mode Original mode 1 2.